Connect the RS-232 cable to your computer and handset, I am using a USB to RS-232 adapter with FTDI chipset.Ĥ Initialize and align your telescope as you normally would. You have to have the ascom upgraded BEFORE trying to install the celestron driver.ģ. Be sure to have the latest version of Ascom (current is 6.1 SP1), you can get it from .Ģ. Okay, here is the method that I have used with success in connecting Starry Night Orion edition with my Orion XT10g telescope:ġ. I guess its just me but if they offered a list with different Orion Synscan models the selection process maybe a bit easier to figure out vs guessing what Celestron model works best with my Orion scope. I'm still getting used to the fact that different brands are using the same manufactures to produce their products. I'm not quite sure why Orion is only mentioned once though in the drop down list. Sometimes I would get an error message telling me the scope connected is not a Celestron so I was lead to believe that I had to use a driver specifically associated with the brand Orion. lol Somebody on another forum suggested using Celestron 5i/8i and NexStar 8/9/11 as you did so I went ahead and tried that but still no luck even after proper alignment. So yes I'm still learning all this as I'm fairly new to this hobby. But after further research I figured out that AZ mounts are used on both tripods and Dobsonian style telescopes. While Sky-watcher seemed to be the closest model that looked identical to mine so I tried working with that. When you are finished, follow the instructions provided by your software to close the connection to the telescopeĪt the time I wrote that I wasn't sure yet if Celestron even had drivers for AZ mounts since the majority of the photos online showed them mounted on tripods. The SynScan AZ should be under the full control of your computer once the connection is successfully established.Ĥ. In the planetarium software of your choice, choose "Sky-Watcher Mount, Celestron NexStar 5i/8i" or "Celestron NexStar 8/9/11" in the driver setup menu and follow the instructions provided by your program to establish the connection to the telescope. Connect the RS-232 cable to the RJ-12 connector on the hand control and to the COM-port of your computer (Fig.o).ģ. Make sure that the telescope has been aligned.Ģ. AZ Version 3.00 and later is compatible with Celestron 5i/8i and NexStar GPS command protocol.ġ. Many commercially available planetarium softwares can be used to control SynScan. I found this documentation that suggests the AZ mount is compatible with the Celestron drivers:Īnother feature of SynScan AZ is the ability to connect to a computer via a serial communication cable. You said " And the Celestron driver seems to only support equatorial mounts from what I see." How do you draw this conclusion? I'm running all this on Windows 7 Professional 64 bit OS. All data in the hand controller is correct based on my current viewing location followed by a thorough 2 star alignment procedure. All I think I need at this point is a proper driver that supports my particular Goto scope so I can access it during the configuring stage and then connect. I've contacted Orion technical support but all they could do for me was submit my claim for further review. And the Celestron driver seems to only support equatorial mounts from what I see. The Orion driver is for the Intelliscope and not the Goto series. The problem now is neither work for my particular telescope. After hearing a few comments online regarding drivers I went back to ASCOM where I was able to download and install both Orion and Celestron drivers. When I'm trying to configure I cannot seem to find my scope listed anywhere. When I'm trying to configure then connect I make sure my hand controller is set to Utilities > Direct to PC. And so far I'm currently running Starry Night ver. Its even recognized in the device manger also. 3.08) so I know that my serial to USB 2.0 adapter is working correctly. I've already managed to upgrade my controller to the latest firmware (ver. You can use the Nexus DSC with planetarium software such as SkySafari Plus/Pro, Starry Night, Cartes du Ciel, TheSky just to name a few.I've been trying to connect my Orion XT12g Newtonian Dobsonian telescope mounted on a Synscan Goto mount to Starry Night. Using the advantages of WiFi (optional module), the Nexus DSC allows for the seamless interfacing of your telescope to the most popular planetarium software running on WiFi-enabled computing devices: iPhone, iPad, iPod Touch, Apple Computers, Android phones/tablets, Kindle Fire, Windows based PCs/tablets. The system is initialized via reference stars and from then on you can unerringly approach any object. Nexus DSC - Advanced Digital Setting CirclesNexus DSC is an advanced digital setting circles computer for your telescope that packs all the latest technologies into a device designed for your telescope.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |